Forums > Help! > How to make a levistick?

Login/Join to Participate

Simon_Magic
stranger

Member Since: 8th Sep 2011
Total posts: 1
Posted:Heya Guys!

I really want to get into Levistick work to use in my Street Shows and on Stage, but I'd really like to make my own.

I currently have a 895mm piece of dowel, and I am just not sure where I am meant to drill holes and so forth.

Any help would be brilliant!

Thanks in advance!

Simon_Magic


Delete Topic

Mynci
Mynci

Macaque of all trades
Location: wombling free...
Member Since: 27th Apr 2005
Total posts: 8737
Posted:just above the balance point. it may take a few goes to get exactly right
I haven't watched the video (at work) but this is a video to make essentially a levistick. Magicians call it a dancing cane:




A couple of balls short of a full cascade... or maybe a few cards short of a deck... we'll see how this all fans out.

Delete

ShadowlessTyger
ShadowlessTyger

Flow Artist
Location: USA
Member Since: 28th Jan 2011
Total posts: 67
Posted:For the location of the connection:

You want the location of the hole to be at the balance point between moment caused by the centrifugal force outward and gravity downward about the center of gravity. There are many ways to make this perfect depending on the speed of which you rock/swing the wand/cane. The faster you spin, the closer to the center away from and the slow you spin, the further away from center. For a beginner, I have found that 1 inch above a perfectly balanced 30 wand/cane to be the best. This will change depending on whether or not you have weight on top or bottom. I prefer to use a slightly bottom heavy wand/cane and then place the center ~2.5% of the length.

For your 895mm, Id say place the hole 20 to 24 mm above the balance point.

Now for the harder part, the length of your loop:

Beginner Flow wands: Hand span past half length. Close enough to stall but long enough to get around.

Magician's cane: Looped (no knots) at 3/4 length to facilitate certain two handed levitations.

Long string is considered anything past 1 full wand/cane/staff length, usually 30 inches or 75 cm.

Loopers/Hoopers or ambidextrous passers will make theirs a little less than wing span but never use the full length.

Double wand (Linked) length is your height if you pass it behind you (magicians) and your height minus your shoulders if you are a front passer (spinners).

The longest I'd recommend (usually rope dart and hammer spinners) is about 1.5 your arm lengths, unless you are very quick at hand wraps.

Other considerations:
Decoration Make sure you use something bright to catch peoples eyes a hoop glitter tape works well.
String Definitely Kevlar thread if you are using a fire ward. Coats and Clark Dual duty for most applications and their 0.004 black nylon if you are a magician.
Weight Your dowel will work well for now, but considering air drag, a slightly tip heavy (more rotational inertia without a lot more weight) tends to work better for keeping your wand/cane perfectly upright.
Rods vs Tubes. tubes are lighter for the width of wand, they can hold much, much more fuel, and can hide the string inside when used just as a baton.

Thats all I can think of for now. Good Luck!


Delete

Mufasa
stranger

Member Since: 17th Sep 2011
Total posts: 1
Posted:My question on this topic is whether, if you over-weight the top or bottom, you can successfully compensate for this by moving the string hole up or down. I'm making a light-up one, and i'm trying to figure out how to balance the electrical components. If the batteries and such are at the top, should I be trying to find an equal weight and sized something to put at the bottom to balance it out? Or can I put something really small but heavy at the bottom and understand that my balance point will be off-center? Does that affect the flow of this?

Delete

Jameth
Jameth

enthusiast
Location: NSW
Member Since: 19th May 2008
Total posts: 378
Posted:I haven't tried it but I would have thought the thing to do would be to find the balance point of your finished stick with all your mods on and work from that.

IMO you'd want to keep it as light as possible overall.


Delete

Braaainz
stranger

Member Since: 27th Aug 2012
Total posts: 4
Posted:Sorry to resurrect an old thread, but I'm making my own to give to friends & possibly sell at festivals.

Do most people prefer a weight on the bottom? If so, any idea how much? Why do you prefer the weight?

Do you prefer finger loop, hand loop, or full loop for the string?
(personally I prefer hand loop. I don't catch the string on the stick as often as I do with the full loop and it still allows me to switch hands easily which I can't do with a fingerloop)

What colors do you like best? Metallic, fluorescent, dark, wood with burnt design?


Delete

Mynci
Mynci

Macaque of all trades
Location: wombling free...
Member Since: 27th Apr 2005
Total posts: 8737
Posted:sould be a large single loop so it can be passed easily from hand to hand. You can also do a lot more tricks with a full loop like spinning levitation between hands and a few others that I have from my magicians tutorial video.

should be no additioinal weight, just stringed slightly above the balance to aid in keeping upright. and i mean JUST above. however if it is off you can always add a bit of tape to get it just right and mix it in with the decorations.


A couple of balls short of a full cascade... or maybe a few cards short of a deck... we'll see how this all fans out.

Delete